walls.one

Material calculators

Acoustical Ceiling Grid and Tile
Calculator.

How many main runners, cross tees, wall angle pieces, hanger wires and ceiling tiles a room takes, for 2 x 2 and 2 x 4 panels, with the border tile size. Add the answer to a material list with the other calculators, then price the list in your order.

calculators
8
rules you can change
23
material list
1
  1. 1 · EnterThe sizes off the plans

  2. 2 · SeeThe count, and how it was worked out

  3. 3 · AddEach answer to one material list

  4. 4 · SendThe list to your order or a submittal

Acoustical Ceiling Grid and Tile

Room sizes in. Main runners, cross tees, wall angle, hanger wire and panels out.

ft
ft

You need about

1062 × 2 panels

384 SF of ceiling in 1 room

  • Ceiling panels, 2′ × 2′

    384 SF with 10% waste. Pick a panel to see cartons.

    106panels

  • 15/16″ main runner, 12′

    Mains 4′ apart, running the length of each room

    7pcs

  • 15/16″ cross tee, 4′

    Between the mains, 2′ apart

    49pcs

  • 15/16″ cross tee, 2′

    Splits each 2′ × 4′ opening for a 2′ × 2′ panel

    53pcs

  • Wall angle, 12′

    Around the walls of each room

    8pcs

  • Hanger wire, 12 ga

    One every 4′ along each main. Seismic bracing and fixtures need more.

    The catalog does not list how many wires are in a bundle. 100 assumed.

    18wires

24′16′
The room in plan, centred. Heavy lines are main runners 4′ apart, the dots are hanger wires, the outline is wall angle. Border panels: 24″ at the ends and 24″ at the sides.

Ordering a ceiling? The ceiling grid builder puts these parts in your order with our item numbers, and the guide walks through the count by hand.

The rules this uses — change them to yours
%
ft

These start at the figures our own takeoffs use. Your changes are kept in this browser and used by every calculator.

Estimates, worked from the sizes you enter and the rules shown under each calculator. Check them against the drawings before you order. Rated and structural walls are built to the tested assembly and the engineer's design, not to a rule of thumb.

Reference

The FiguresBehind the Answers.

A count is a size multiplied by a rule. These are the rules and the weights the calculators start from. The weights are the manufacturers' published figures for what we sell.

Studs in 100 ft of wall

Length over spacing, plus one. No openings or corners.

  • 12″ on centre101 studs
  • 16″ on centre76 studs
  • 24″ on centre51 studs

Weight of a 3-5/8″ stud

Pounds per foot, by gauge. ClarkDietrich ProSTUD.

  • 25 ga EQ · 15 mil0.3 lb/ft
  • 20 ga EQ · 18 mil0.4 lb/ft
  • 20 ga DW · 30 mil0.7 lb/ft
  • 20 ga · 33 mil0.8 lb/ft

Weight of a 4 × 12 sheet

Pounds, by board. CertainTeed published weights.

  • Type X Drywall105.6 lb
  • 1/4" Regular Drywall54.2 lb
  • 3/8" Regular Drywall60 lb
  • Easi-Lite® Lightweight Drywall62.4 lb
  • 1/2" M2Tech® Drywall76.8 lb
  • 5/8" M2Tech® Drywall105.6 lb
  • 1/2" GlasRoc® Interior Drywall86.4 lb
  • 5/8" GlasRoc® Interior Drywall115.2 lb
MaterialThe rule we start fromFor 1,000 SF of board
Joint tape0.37 LF for each SF of board370 LF, one 500′ roll
All-purpose compound, taping coat1 box (3.5 gal) covers 850 SF1.2 boxes
Topping compound, two finish coats1 box (3.5 gal) covers 700 SF1.4 boxes
Drywall screws, framing 24″ o.c.0.75 for each SF750 screws, about 2.5 lb
Drywall screws, framing 16″ o.c.1.13 for each SF1125 screws, about 3.8 lb
Level 5 primer-surfacer1 gallon covers 110 SF10 gallons
Board waste10%23 sheets of 4 × 12

After the count

Three Things to DoWith a Material List.

Price it in your order

The list opens matched to our catalog with the sizes you chose. Change a quantity or a brand, then request a quote or place the order.

Back to the list

Build the submittal

The same products go to the submittal builder, which binds each manufacturer's data sheet into one PDF with your part numbers marked.

Open the submittal builder

Have the plans taken off

For a full set of drawings, upload the bid documents. We measure every wall and ceiling and send back the takeoff, an Excel bid sheet and a quote.

See the AI takeoff service

Questions

How theCounts Are Made.

The rules behind each calculator, in a sentence or two.

How many metal studs do I need for a wall?

Divide the wall length in inches by the stud spacing and add one. A 48 ft wall at 16 inches on centre is 37 studs. Then add two for each door or window, two for each corner and one for each free end, and about 5% for waste. The metal studs calculator does this and adds the track.

How many sheets of drywall do I need?

Multiply the wall length by the height, and by two if both sides get board. Take out about 21 square feet for a door and 15 for a window, add 10% for waste, and divide by the area of one sheet: 32 square feet for a 4 × 8, 48 for a 4 × 12.

How much joint compound and tape does drywall take?

For a Level 4 finish we figure one 3.5 gallon box of all-purpose compound for every 850 square feet of board for the taping coat, one box of topping compound for every 700 square feet for the two finish coats, and 370 feet of tape for every 1,000 square feet. You can change each figure to your own.

How do I figure a suspended ceiling grid?

Main runners run the length of the room, 4 ft apart. Four-foot cross tees go between them every 2 ft. A 2 × 2 ceiling adds a 2 ft cross tee in each opening. Wall angle goes around the room, and a hanger wire carries each main every 4 ft. Enter the room size and the ceiling calculator counts each part.

Where do the waste factors and coverage figures come from?

They are the figures we use for our own takeoffs: 10% waste on board, 5% on framing and insulation, 10% on ceilings and trim. Each calculator shows the rules it used under its result, and every one of them can be changed. Your changes are kept in your browser.

Can I order what the calculator gives me?

Yes. Add each answer to the material list, then press Price it in your order. The list opens matched to our catalog with the sizes you chose. Items with a list price are priced straight away and the rest go to our desk for a number. Nothing is ordered until you check out.

Are these numbers good enough to bid from?

They are estimates from simple rules, good for a small job, a change order or a check on somebody else's count. For a bid on a full set of plans, use the AI takeoff service: it measures every wall and ceiling on the drawings.

Do the calculators work for rated or structural walls?

They count material. They do not design a wall. A fire-rated or sound-rated wall is built to its tested assembly, and a structural or exterior wall to the engineer's design, so take the stud size, gauge and spacing from those and use the calculator for the quantities.