walls.one

Material calculators

Suspended Drywall Ceiling
Calculator.

Material for a suspended drywall ceiling: drywall grid or cold-rolled channel and furring channel, hanger wire, board and screws, from the room size. Add the answer to a material list with the other calculators, then price the list in your order.

calculators
8
rules you can change
23
material list
1
  1. 1 · EnterThe sizes off the plans

  2. 2 · SeeThe count, and how it was worked out

  3. 3 · AddEach answer to one material list

  4. 4 · SendThe list to your order or a submittal

Suspended Drywall Ceiling

Room size in. Drywall grid or channel and furring, hanger wire, board and screws out.

ft
ft

You need about

7sheets, 4′ × 12′

280 SF of ceiling · 3 lines of carrying channel · about 842 lb

  • Cold-rolled channel, 1-1/2″, 16′

    3 lines of carrying channel 4′ apart, 60 LF

    4pcs31 lb

  • Furring channel, 7/8″, 12′

    16 runs at 16″ o.c. across the channel, 224 LF

    20pcs72 lb

  • Furring clips or tie wire

    One where each furring channel crosses a carrying channel

    Clips or tie wire are not matched to the catalog. Add them as a note.

    48ties

  • Hanger wire, 12 ga

    One every 4′ along each carrier

    The catalog does not list how many wires are in a bundle. 100 assumed.

    18wires

  • Type X Drywall, 4′ × 12′

    280 SF of ceiling, 10% waste

    7sheets739 lb

  • Drywall screws, 1-1/4″ fine thread

    1.13 per SF on framing 16″ o.c.

    The catalog does not list how many are in a box. 5,000 assumed for 1-1/4″.

    315screws

20′14′
The ceiling in plan. Heavy lines are the carrying channels 4′ apart with a hanger wire at each dot; the light lines are the furring channels the board screws to.
The rules this uses — change them to yours
%
%
ea
ft

These start at the figures our own takeoffs use. Your changes are kept in this browser and used by every calculator.

Estimates, worked from the sizes you enter and the rules shown under each calculator. Check them against the drawings before you order. Rated and structural walls are built to the tested assembly and the engineer's design, not to a rule of thumb.

Reference

The FiguresBehind the Answers.

A count is a size multiplied by a rule. These are the rules and the weights the calculators start from. The weights are the manufacturers' published figures for what we sell.

Studs in 100 ft of wall

Length over spacing, plus one. No openings or corners.

  • 12″ on centre101 studs
  • 16″ on centre76 studs
  • 24″ on centre51 studs

Weight of a 3-5/8″ stud

Pounds per foot, by gauge. ClarkDietrich ProSTUD.

  • 25 ga EQ · 15 mil0.3 lb/ft
  • 20 ga EQ · 18 mil0.4 lb/ft
  • 20 ga DW · 30 mil0.7 lb/ft
  • 20 ga · 33 mil0.8 lb/ft

Weight of a 4 × 12 sheet

Pounds, by board. CertainTeed published weights.

  • Type X Drywall105.6 lb
  • 1/4" Regular Drywall54.2 lb
  • 3/8" Regular Drywall60 lb
  • Easi-Lite® Lightweight Drywall62.4 lb
  • 1/2" M2Tech® Drywall76.8 lb
  • 5/8" M2Tech® Drywall105.6 lb
  • 1/2" GlasRoc® Interior Drywall86.4 lb
  • 5/8" GlasRoc® Interior Drywall115.2 lb
MaterialThe rule we start fromFor 1,000 SF of board
Joint tape0.37 LF for each SF of board370 LF, one 500′ roll
All-purpose compound, taping coat1 box (3.5 gal) covers 850 SF1.2 boxes
Topping compound, two finish coats1 box (3.5 gal) covers 700 SF1.4 boxes
Drywall screws, framing 24″ o.c.0.75 for each SF750 screws, about 2.5 lb
Drywall screws, framing 16″ o.c.1.13 for each SF1125 screws, about 3.8 lb
Level 5 primer-surfacer1 gallon covers 110 SF10 gallons
Board waste10%23 sheets of 4 × 12

After the count

Three Things to DoWith a Material List.

Price it in your order

The list opens matched to our catalog with the sizes you chose. Change a quantity or a brand, then request a quote or place the order.

Back to the list

Build the submittal

The same products go to the submittal builder, which binds each manufacturer's data sheet into one PDF with your part numbers marked.

Open the submittal builder

Have the plans taken off

For a full set of drawings, upload the bid documents. We measure every wall and ceiling and send back the takeoff, an Excel bid sheet and a quote.

See the AI takeoff service

Questions

How theCounts Are Made.

The rules behind each calculator, in a sentence or two.

How many metal studs do I need for a wall?

Divide the wall length in inches by the stud spacing and add one. A 48 ft wall at 16 inches on centre is 37 studs. Then add two for each door or window, two for each corner and one for each free end, and about 5% for waste. The metal studs calculator does this and adds the track.

How many sheets of drywall do I need?

Multiply the wall length by the height, and by two if both sides get board. Take out about 21 square feet for a door and 15 for a window, add 10% for waste, and divide by the area of one sheet: 32 square feet for a 4 × 8, 48 for a 4 × 12.

How much joint compound and tape does drywall take?

For a Level 4 finish we figure one 3.5 gallon box of all-purpose compound for every 850 square feet of board for the taping coat, one box of topping compound for every 700 square feet for the two finish coats, and 370 feet of tape for every 1,000 square feet. You can change each figure to your own.

How do I figure a suspended ceiling grid?

Main runners run the length of the room, 4 ft apart. Four-foot cross tees go between them every 2 ft. A 2 × 2 ceiling adds a 2 ft cross tee in each opening. Wall angle goes around the room, and a hanger wire carries each main every 4 ft. Enter the room size and the ceiling calculator counts each part.

Where do the waste factors and coverage figures come from?

They are the figures we use for our own takeoffs: 10% waste on board, 5% on framing and insulation, 10% on ceilings and trim. Each calculator shows the rules it used under its result, and every one of them can be changed. Your changes are kept in your browser.

Can I order what the calculator gives me?

Yes. Add each answer to the material list, then press Price it in your order. The list opens matched to our catalog with the sizes you chose. Items with a list price are priced straight away and the rest go to our desk for a number. Nothing is ordered until you check out.

Are these numbers good enough to bid from?

They are estimates from simple rules, good for a small job, a change order or a check on somebody else's count. For a bid on a full set of plans, use the AI takeoff service: it measures every wall and ceiling on the drawings.

Do the calculators work for rated or structural walls?

They count material. They do not design a wall. A fire-rated or sound-rated wall is built to its tested assembly, and a structural or exterior wall to the engineer's design, so take the stud size, gauge and spacing from those and use the calculator for the quantities.